MNC-12x5/Src/board.c

#include "board.h"

/* private functions */
static void TIM1_Init(void);
static void TIM3_Init(void);
static void TIM14_Init(void);
static void TIM16_Init(void);
static void TIM17_Init(void);

/* Board perephireal Configuration  */
void Board_Init(void)
{
  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  RCC->APBENR2 |= RCC_APBENR2_SYSCFGEN;
  RCC->APBENR1 |= RCC_APBENR1_PWREN;

  /* Peripheral interrupt init*/
  /* RCC_IRQn interrupt configuration */
  NVIC_SetPriority(RCC_IRQn, 0);
  NVIC_EnableIRQ(RCC_IRQn);

  /* Configure the system clock */
  SystemClock_Config();

  /* Processor uses sleep as its low power mode */
  SCB->SCR &= ~((uint32_t)SCB_SCR_SLEEPDEEP_Msk);
  /* DisableSleepOnExit */
  SCB->SCR &= ~((uint32_t)SCB_SCR_SLEEPONEXIT_Msk);

  /* в дейтвительности нигде не используеться? */
  //LL_RCC_GetSystemClocksFreq(&rcc_clocks); :::
  /* Get SYSCLK frequency */
  ///RCC_Clocks->SYSCLK_Frequency = RCC_GetSystemClockFreq();
  /* HCLK clock frequency */
  ///RCC_Clocks->HCLK_Frequency   = RCC_GetHCLKClockFreq(RCC_Clocks->SYSCLK_Frequency);
  /* PCLK1 clock frequency */
  ///RCC_Clocks->PCLK1_Frequency  = RCC_GetPCLK1ClockFreq(RCC_Clocks->HCLK_Frequency);

  /* Initialize all configured peripherals */

  /* Start RGB & Tube Power PWM */
	TIM1_Init();
  TIM3_Init();

	TIM14_Init();

  TIM16_Init();
  TIM17_Init();
}

/**
  * @brief System Clock Configuration
  * @retval None
  */
void SystemClock_Config(void)
{
  /* HSI configuration and activation */
  RCC->CR |= RCC_CR_HSIKERON; // Enable HSI even in stop mode
  while((RCC->CR & RCC_CR_HSIRDY) == 0)
  {
  }

  /* Main PLL configuration and activation */
  RCC->PLLCFGR &= ~(RCC_PLLCFGR_PLLSRC | RCC_PLLCFGR_PLLM | RCC_PLLCFGR_PLLN | RCC_PLLCFGR_PLLR);
  RCC->PLLCFGR |= (RCC_PLLCFGR_PLLSRC_HSI | RCC_PLLCFGR_PLLM_0 | (9 << RCC_PLLCFGR_PLLN_Pos) | RCC_PLLCFGR_PLLM_1);
  RCC->CR |= RCC_CR_PLLON; // RCC_PLL_Enable
  RCC->PLLCFGR |= RCC_PLLCFGR_PLLREN; // RCC_PLL_EnableDomain_SYS
  while((RCC->CR & RCC_CR_PLLRDY) == 0)
  {
  }

  /* Set AHB prescaler*/
  RCC->CFGR &= ~(RCC_CFGR_HPRE);
  RCC->CFGR |= 0x00000000U;

  /* Sysclk activation on the main PLL */
  RCC->CFGR &= RCC_CFGR_SW;
  RCC->CFGR |= RCC_CFGR_SW_1;
  while((RCC->CFGR & RCC_CFGR_SWS) != RCC_CFGR_SWS_1)
  {
  }

  /* Set APB1 prescaler*/
  RCC->CFGR &= RCC_CFGR_PPRE;
  RCC->CFGR |= 0x00000000U;

#ifdef USES_SYSTICK
  /* Configure the SysTick to have interrupt in 1ms time base */
  SysTick->LOAD  = (uint32_t)((24000000 / 1000) - 1UL);  /* set reload register */
  SysTick->VAL   = 0UL;                                  /* Load the SysTick Counter Value */
  SysTick->CTRL  = SysTick_CTRL_CLKSOURCE_Msk |
                   SysTick_CTRL_ENABLE_Msk;              /* Enable the Systick Timer */
#endif

  /* Update CMSIS variable (which can be updated also through SystemCoreClockUpdate function) */
  SystemCoreClock = 24000000;

  /* SetI2CClockSource */
  RCC->CCIPR &= ~(((RCC_CCIPR_I2C1SEL << 16U) | RCC_CCIPR_I2C1SEL_1) >> 16U);
  RCC->CCIPR |= (((RCC_CCIPR_I2C1SEL << 16U) | RCC_CCIPR_I2C1SEL_1) & 0x0000FFFFU);
}

/**
  * @brief TIM1 Initialization Function
  * @param None
  * @retval None
  */
static void TIM1_Init(void)
{
  /* Peripheral clock TIM1 enable */
	RCC->APBENR2 |= RCC_APBENR2_TIM1EN;
  /* Peripheral clock GPIOA enable */
	RCC->IOPENR |= RCC_IOPENR_GPIOAEN;

  /* target clock - 200 Hz */
  TIM1->PSC = TIM1_PSC; // prescaler
  TIM1->ARR = TIM1_ARR; // auto reload value
  TIM1->CR1 = TIM_CR1_ARPE;
  // initial pwm value
  TIM1->CCR1 = PWM_TUBE_INIT_VAL;
  TIM1->CCR2 = PWM_LED_INIT_VAL;
  TIM1->CCR3 = PWM_LED_INIT_VAL;
  TIM1->CCR4 = PWM_LED_INIT_VAL;
  // pwm mode 1 for 4 chanels
  TIM1->CCMR1 = (TIM_CCMR1_OC1M_1 | TIM_CCMR1_OC1M_2 | TIM_CCMR1_OC2M_1 | TIM_CCMR1_OC2M_2 | TIM_CCMR1_OC1PE | TIM_CCMR1_OC2PE);
  TIM1->CCMR2 = (TIM_CCMR2_OC3M_1 | TIM_CCMR2_OC3M_2 | TIM_CCMR2_OC4M_1 | TIM_CCMR2_OC4M_2 | TIM_CCMR2_OC3PE | TIM_CCMR2_OC4PE);
  // reset int flag - not needed, int unused
  //TIM1->SR |= TIM_SR_UIF;
  TIM1->BDTR = TIM_BDTR_MOE; // enable main output
  TIM1->EGR = TIM_EGR_UG; // force timer update
  /* TIM1 CC_EnableChannel */
  TIM1->CCER = (TIM_CCER_CC1E | TIM_CCER_CC2E | TIM_CCER_CC3E | TIM_CCER_CC4E);
  /* TIM_EnableCounter */
  TIM1->CR1 |= TIM_CR1_CEN;


  /** TIM1 GPIO Configuration
		PA8 ------> TIM1_CH1
		PA9 ------> TIM1_CH2
		PA10 ------> TIM1_CH3
		PA11 [PA9] ------> TIM1_CH4
  */
  GPIO_SetPinMode(PWM_1_GPIO_Port, PWM_1_Pin, GPIO_MODE_AFF);
  GPIO_SetPinSpeed(PWM_1_GPIO_Port, PWM_1_Pin, GPIO_OSPEED_HI);
  GPIO_SetPinPull(PWM_1_GPIO_Port, PWM_1_Pin, GPIO_PUPDR_DW);
  GPIO_SetAFPin_8_15(PWM_1_GPIO_Port, PWM_1_Pin, GPIO_AF_2);

  GPIO_SetPinMode(PWM_R_GPIO_Port, PWM_R_Pin, GPIO_MODE_AFF);
  GPIO_SetPinSpeed(PWM_R_GPIO_Port, PWM_R_Pin, GPIO_OSPEED_HI);
  GPIO_SetPinPull(PWM_R_GPIO_Port, PWM_R_Pin, GPIO_PUPDR_DW);
  GPIO_SetAFPin_8_15(PWM_R_GPIO_Port, PWM_R_Pin, GPIO_AF_2);

  GPIO_SetPinMode(PWM_B_GPIO_Port, PWM_B_Pin, GPIO_MODE_AFF);
  GPIO_SetPinSpeed(PWM_B_GPIO_Port, PWM_B_Pin, GPIO_OSPEED_HI);
  GPIO_SetPinPull(PWM_B_GPIO_Port, PWM_B_Pin, GPIO_PUPDR_DW);
  GPIO_SetAFPin_8_15(PWM_B_GPIO_Port, PWM_B_Pin, GPIO_AF_2);

  GPIO_SetPinMode(PWM_G_GPIO_Port, PWM_B_Pin, GPIO_MODE_AFF);
  GPIO_SetPinSpeed(PWM_G_GPIO_Port, PWM_B_Pin, GPIO_OSPEED_HI);
  GPIO_SetPinPull(PWM_G_GPIO_Port, PWM_B_Pin, GPIO_PUPDR_DW);
  GPIO_SetAFPin_8_15(PWM_G_GPIO_Port, PWM_B_Pin, GPIO_AF_2);
}

/**
  * @brief TIM3 Initialization Function
  * @param None
  * @retval None
  */
static void TIM3_Init(void)
{
  /* Peripheral clock TIM1 enable */
	RCC->APBENR1 |= RCC_APBENR1_TIM3EN;
  /* Peripheral clock GPIOA and GPIOB enable */
	RCC->IOPENR |= (RCC_IOPENR_GPIOAEN | RCC_IOPENR_GPIOBEN);

  /* target clock - 200 Hz */
  TIM3->PSC = TIM3_PSC; // prescaler
  TIM3->ARR = TIM3_ARR; // auto reload value
  TIM3->CR1 = TIM_CR1_ARPE;
  // initial pwm value
  TIM3->CCR1 = PWM_TUBE_INIT_VAL;
  TIM3->CCR2 = PWM_TUBE_INIT_VAL;
  TIM3->CCR3 = PWM_TUBE_INIT_VAL;
  TIM3->CCR4 = PWM_TUBE_INIT_VAL;
  // pwm mode 1 for 4 chanels
  TIM3->CCMR1 = (TIM_CCMR1_OC1M_1 | TIM_CCMR1_OC1M_2 | TIM_CCMR1_OC2M_1 | TIM_CCMR1_OC2M_2 | TIM_CCMR1_OC1PE | TIM_CCMR1_OC2PE);
  TIM3->CCMR2 = (TIM_CCMR2_OC3M_1 | TIM_CCMR2_OC3M_2 | TIM_CCMR2_OC4M_1 | TIM_CCMR2_OC4M_2 | TIM_CCMR2_OC3PE | TIM_CCMR2_OC4PE);
  // launch timer
  TIM3->EGR = TIM_EGR_UG; // force timer update
  /* TIM3 TIM_CC_EnableChannel */
  TIM3->CCER = (TIM_CCER_CC1E | TIM_CCER_CC2E | TIM_CCER_CC3E | TIM_CCER_CC4E);
  /* TIM3 enable */
  TIM3->CR1 |= TIM_CR1_CEN;

  /**TIM3 GPIO Configuration
  PA6   ------> TIM3_CH1
  PA7   ------> TIM3_CH2
  PB0   ------> TIM3_CH3
  PB1   ------> TIM3_CH4
  */
  GPIO_SetPinMode(PWM_5_GPIO_Port, PWM_5_Pin, GPIO_MODE_AFF);
  GPIO_SetPinSpeed(PWM_5_GPIO_Port, PWM_5_Pin, GPIO_OSPEED_HI);
  GPIO_SetPinPull(PWM_5_GPIO_Port, PWM_5_Pin, GPIO_PUPDR_DW);
  GPIO_SetAFPin_0_7(PWM_5_GPIO_Port, PWM_5_Pin, GPIO_AF_1);

  GPIO_SetPinMode(PWM_4_GPIO_Port, PWM_4_Pin, GPIO_MODE_AFF);
  GPIO_SetPinSpeed(PWM_4_GPIO_Port, PWM_4_Pin, GPIO_OSPEED_HI);
  GPIO_SetPinPull(PWM_4_GPIO_Port, PWM_4_Pin, GPIO_PUPDR_DW);
  GPIO_SetAFPin_0_7(PWM_4_GPIO_Port, PWM_4_Pin, GPIO_AF_1);

  GPIO_SetPinMode(PWM_3_GPIO_Port, PWM_3_Pin, GPIO_MODE_AFF);
  GPIO_SetPinSpeed(PWM_3_GPIO_Port, PWM_3_Pin, GPIO_OSPEED_HI);
  GPIO_SetPinPull(PWM_3_GPIO_Port, PWM_3_Pin, GPIO_PUPDR_DW);
  GPIO_SetAFPin_0_7(PWM_3_GPIO_Port, PWM_3_Pin, GPIO_AF_1);

  GPIO_SetPinMode(PWM_2_GPIO_Port, PWM_2_Pin, GPIO_MODE_AFF);
  GPIO_SetPinSpeed(PWM_2_GPIO_Port, PWM_2_Pin, GPIO_OSPEED_HI);
  GPIO_SetPinPull(PWM_2_GPIO_Port, PWM_2_Pin, GPIO_PUPDR_DW);
  GPIO_SetAFPin_0_7(PWM_2_GPIO_Port, PWM_2_Pin, GPIO_AF_1);
}

/**
  * @brief TIM14 Initialization Function
  * @param None
  * @retval None
  * @desc   "Блинкование" разрядами - 0,75/0,25 сек вкл/выкл.
  */
static void TIM14_Init(void)
{
  /* Peripheral clock enable */
  RCC->APBENR2 |= RCC_APBENR2_TIM14EN;

  /* TIM14 interrupt Init */
  NVIC_SetPriority(TIM14_IRQn, 0);
  NVIC_EnableIRQ(TIM14_IRQn);

  /* Set TIM14 for 1 sec period  */
  TIM14->PSC = TIM14_PSC;
  TIM14->ARR = TIM14_ARR;

  /* Enable:  Auto-reload preload, One-pulse mode, */
  TIM14->CR1 = (TIM_CR1_ARPE | TIM_CR1_OPM);

  /* OC or PWM? (for pwm - (TIM_CCMR1_OC1M_2 | TIM_CCMR1_OC1M_1) ) , Output compare 1 preload */
  TIM14->CCMR1 = (TIM_CCMR1_OC1M_0 | TIM_CCMR1_OC1PE);

  /* Enable Channel_1 or no needed ??? */
  TIM14->CCER = TIM_CCER_CC1E;

  /* Impulse value in msek */
  TIM14->CCR1 = TIM14_PULSE_VAL;

  /* Enable IRQ for Update end CaptureCompare envents or only CC ??? */
  //TIM14->DIER = (TIM_DIER_UIE | TIM_DIER_CC1IE);
  TIM14->DIER = TIM_DIER_CC1IE;
}

/**
 * На старте активируем все каналы, при совпадении отключаем (не)нужные.
 */
void Blink_Start(void)
{
	/* enable all channels */
	TUBE_ALL_ON;

	/* clear IRQ flag */
  TIM14->SR |= TIM_SR_CC1IF;

  /* clear counter value */
  TIM14->CNT = 0;

  /* enable timer */
  TIM14->CR1 |= TIM_CR1_CEN;
}

void Blink_Stop(void)
{
  /* disable timer */
  TIM14->CR1 &= ~(TIM_CR1_CEN);
  /* On all tubes */
  TUBE_ALL_ON;
}

/**
  * @brief TIM16 Initialization Function
  * @param None
  * @retval None
  */
static void TIM16_Init(void)
{
  /* Peripheral clock enable */
  RCC->APBENR2 |= RCC_APBENR2_TIM16EN;

  /* TIM16 interrupt Init */
  NVIC_SetPriority(TIM16_IRQn, 0);
  NVIC_EnableIRQ(TIM16_IRQn);

  /* setup clock */
  TIM16->PSC = TIM16_PSC; // prescaler
  TIM16->ARR = TIM16_ARR; // auto reload value
  TIM16->CR1 = TIM_CR1_ARPE;
  // initial pwm value
  //TIM16->CCR1 = TIM16_PWM_VAL;
  // pwm mode 1 for 1 chanel
  TIM16->CCMR1 = (TIM_CCMR1_OC1M_1 | TIM_CCMR1_OC1M_2 | TIM_CCMR1_OC1PE);
  // reset int flag
  TIM16->SR |= TIM_SR_UIF;
  TIM16->BDTR = TIM_BDTR_MOE; // enable main output
  TIM16->EGR = TIM_EGR_UG; // force timer update
  /* TIM16 CC_EnableChannel */
  TIM16->CCER = TIM_CCER_CC1E;
  /* TIM_EnableCounter */
  TIM16->CR1 |= TIM_CR1_CEN;
  /* Enable IRQ */
  TIM16->DIER = TIM_DIER_UIE;
}

/**
  * @brief TIM17 Initialization Function
  * @param None
  * @retval None
  */
static void TIM17_Init(void)
{
  /* Peripheral clock enable */
  RCC->APBENR2 |= RCC_APBENR2_TIM17EN;

  /* TIM17 interrupt Init */
  NVIC_SetPriority(TIM17_IRQn, 0);
  NVIC_EnableIRQ(TIM17_IRQn);

  /* setup clock */
  TIM17->PSC = TIM17_PSC; // prescaler
  TIM17->ARR = TIM17_ARR; // auto reload value
  TIM17->CR1 = TIM_CR1_ARPE;
  // initial pwm value
  //TIM17->CCR1 = TIM17_PWM_VAL;
  // pwm mode 1 for 1 chanel
  TIM17->CCMR1 = (TIM_CCMR1_OC1M_1 | TIM_CCMR1_OC1M_2 | TIM_CCMR1_OC1PE);
  // reset int flag
  TIM17->SR |= TIM_SR_UIF;
  TIM17->BDTR = TIM_BDTR_MOE; // enable main output
  TIM17->EGR = TIM_EGR_UG; // force timer update
  /* TIM17 CC_EnableChannel */
  TIM17->CCER = TIM_CCER_CC1E;
  /* TIM_EnableCounter */
  TIM17->CR1 |= TIM_CR1_CEN;
  /* Enable IRQ */
  TIM17->DIER = TIM_DIER_UIE;
}